ДОСЛІДЖЕННЯ УЩІЛЬНЕННЯ КОМПОЗИТІВ ALN-TIB2 МЕТОДОМ ГАРЯЧОГО СПІКАННЯ

Заголовок (англійською): 
STUDY ON THE DENSIFICATION OF ALN-TIB2 COMPOSITES BY HOT PRESSED SINTERING
Автор(и): 
Li Ming
Ключові слова (укр): 
нітрид алюмінію; борид титану; гаряче пресування спікання; ущільнення
Ключові слова (англ): 
aluminum nitride; titanium boride; hot pressed sintering; densification
Анотація (укр): 
Композити AlN-TiB2 були отримані методом спікання гарячим пресуванням, досліджено вплив вмісту TiB2 та процесу спікання на ущільнення композитів AlN-TiB2. Результати показали, що при 1900℃ протягом 1 год відносна густина досягала понад 98,6% і вміст TiB2 не впливав на процес ущільнення композитів. Також досліджено фазовий склад і мікроструктуру композитів. Двофазні BN і TiN новоутворюються в процесі спікання багатофазного матеріалу AlN-TiB2, тому багатофазний матеріал складається з чотирьох фаз, первинна кристалічна фаза - AlN і TiB2, а вторинна кристалічна фаза – BN і TiN. З підвищенням температури спікання і подовженням часу витримки щільність багатофазних матеріалів AlN-TiB2 поступово зростає. Оптимальна температура спікання та час витримки становили 1900 ℃ та 1 год відповідно. Додавання TiB2 не впливає на спікання багатофазних матеріалів. Багатофазні матеріали досягли і набули високої щільності.
Анотація (англ): 
The AlN-TiB2 composites were prepared by hot pressing sintering process and the effects of TiB2 content and sintering process on the densification of AlN-TiB2 composites were studied. The results showed that at 1900℃ for 1h, the relative density reached more than 98.6% and the TiB2 content had no effect on densification of the composites. The phase composition and microstructure of the composites were also studied. Two-phase BN and TiN are newly formed in the sintering process of AlN-TiB2 multiphase material, so the multiphase material is composed of four phases, the primary crystal phase is AlN and TiB2, and the secondary crystal phase is BN and TiN. With the increase of sintering temperature and the extension of holding time, the density of AlN-TiB2 multiphase materials gradually increases. The optimum sintering temperature and holding time were 1900℃ and 1h respectively. The addition of TiB2 does not affect the sintering of multiphase materials.The multiphase materials have achieved high density.
Публікатор: 
Київський національний університет будівництва і архітектури
Назва журналу, номер, рік випуску (укр): 
Управління розвитком складних систем, номер 48, 2021
Назва журналу, номер, рік випуску (рус): 
Управление развитием сложных систем, номер 48, 2021
Назва журналу, номер, рік випуску (англ): 
Management of Development of Complex Systems, Number 48, 2021
Мова статті: 
English
Формат документа: 
application/pdf
Документ: 
Дата публікації: 
19 Ноябрь 2021
Номер збірника: 
Розділ: 
УПРАВЛІННЯ ТЕХНОЛОГІЧНИМИ ПРОЦЕСАМИ
Університет автора: 
Yancheng Polytechnic College, School of Intelligent Manufacturing, China; Taras Shevchenko National University of Kyiv, Kyiv
Литература: 
  1. Tummala, R R. (1991). Ceramic and glass-ceramic pack-aging in the 1900 s. [J]. J Am Ceram Soc, 74 (5), 895–897.
  2. Watari, K., Ishiaki, K., Tsuchiya, F. (1993). Phonon scattering and thermal conduction mechanisms of sintered aluminum nitride ceramics. [J]. J Mater Sci, 28(8), 3709–3712.
  3. Hengde, L., & Jimei, X. (1990). Material surface and interface [M]. BeiJing, 105.
  4. Mikijelj, B, David, K A, Hutcheon, R. (2003). AlN-based lossy ceramics for high average power microwave devices performance-property correlation. [J]. Journal of the European Ceramic Society, 23 (14), 2705.
  5. David, K. B. (2002). AlN-based lossy ceramics for high power applications. [J]. IEEE International Vacuum Electronics Conference, California, USA, (2), 32–33.
  6. Li, X., Qiu, T., Wu, H., Shen, C. (2005). Study on densification behavior and microwave attenuation characteristic sin AlN/SiC composites. [J]. Material Science Forum, 475–479, 1291–1294.
  7. Khan, A. A., Labbe, J. C. (1996). Aluminum nitride-molybdenum ceramic matrix composites: characterization of ceramics-metal interface. [J]. Journal of the European ceramic Society, (16), 739.
  8. Khan, A. A., Labbe, J. C. (1997). Aluminum nitride-molybdenum ceramic matrix composites: influence of molybdenum addition on electrical, mechanical and thermal properties. [J]. Journal of the European ceramic Society, 17, 1885.
  9. Khan, A. A., Labbe, J. C. (1997). Aluminum nitride-molybdenum ceramic matrix composites possessing high thermal shock resistance. [J]. Materials Science and Engineering, A (230), 33.
  10. Slack, G. A., Tanzilli, R. A., Pohl, R. O., et al. (1987). The intrinsic thermal conductivity of AlN. [J]. J Phys Chem Solids, 48, 641.
  11. Watari, K, Ishiaki, K, Tsuchiya, F. (1993). Phonon scattering and thermal conduction mechanisms of sintered aluminum nitride ceramics. [J]. J Mater Sci, 28, 3709.
  12. David, K. B. (2002). AlN-based lossy ceramics for high power applications. [J]. IEEE International Vacuum Electronics Conference, California, USA, 2, 32–33.